The diploma thesis contains recherche in the area of the tram vehicles. After that it specifies appropriate materials and determines manufacturing method. The design of the axlebridge for narrow gauge tram was made in software CATIA V5. Stress analysis of the mechanical design, whi...

The diploma thesis contains a design of a fineblanking tool for shear cutting the sheet metal components, i.e. the production of a total of six types of sheet metal samples for mechanical tests. Part of the thesis is the optimization of individual construction nodes and F...

Diploma thesis deals with mechanical design of an upright and eletric motor assembly for race car Formula Student. Design of electric motor has been made with regard to optimal cooling. For an upright design has been made Structural analysis and topological optimization using FEM&#...

This thesis consists of engineering design of a trolleybus electric equipment box, which is developed on the bases of the existing solution. At the end both solutions, existing and new design, are compared with special regard to construction stability and technological design.

This diploma thesis contains a design of disassembly tool for a product made of polymeric material intended for application in the automotive industry to check the tightness of the fuel system. The conceptual designs were compared according to the weighted evaluation of the selecte...

The diploma thesis contains a design of a device for testing automotive components. It focuses on the solution of important elements of the equipment and the selection of their suitable variants. The design and calculation of the pressure vessel is also performed, which is the...

The diploma thesis contains a brief overview of planetary gearboxes designed by competitors. The main focus of the work is the design of a planetary gearbox for the first generation of the Formula Student car with electric drive, which is being developed at the University ...

The aim of the diploma thesis is to design a machine for deep drawing and testing of sheet metals. A double-acting hydraulic press with a blank holder is designed for a maximum force of 1,5 MN (of which 0,7 MN falls on the holder). The press should&...

The diploma thesis is focused on the design of a hydraulic upper ejector implemented in the press slide of the Šmeral Brno a.s. company press SKL 2500. The work contains a research on the topic of forging technology, variant designs of hydraulic ejectors with a selection&...

The thesis contains a theoretical analysis of tensioning systems of V-belts. In the thesis, an analysis of the current solution was carried out and subsequently new designs of V-belt tensioners were created. Dynamic simulation was performed for the new designs to determine the load...

This Diploma thesis deserts on a design of an electrically powered low-weight wheelchair, requirements specification with regard to their functionality, analysis of technical solution and individual variants. The resulting concept is further verified using CAE methods

Diploma thesis consists of overview of 3D printing technologies, designing, prototyping and practical testing of specific parts from a car seat.

The aim of the work is to design the coupling and filling circuit for increased control pressure. The dimensioning will be performed for a press with a nominal force of 25 MN. The clutch will be controlled by a pneumatic circuit.

The diploma thesis contains a design of the main drive of the horizontal boring machine HCW2 from the company ŠKODA MACHINE TOOL. The introduction describes the company ŠKODA MACHINE TOOL Furthermore, the work contains the determination of the engine and the design of gears fo...

Design of a bogie frame for Jakobs bogie with an inner frame. The frame design includes a strength calculation according to EN 13 749 for vertical and transverse exceptional loads case. The design is taken into account according to EN 12 663-1, EN 15 08...

This Master's thesis considers the matter of dynamic seat comfort modeling and the effect of frequency-dependent behaviour of automobile seat foams on passengers' comfort. It aims to establish a simulation method enabling an analysis of the seat comfort while the seat is loaded&...

Design of a device for robotic tool exchange with usage of a movable robotic arm at HCW 2 milling machine, made by SMT a.s. company in Pilsen. Diploma work is analyzing a suitable space in an already built or being built a concrete foundation of HCW 2 machine.&#...

The diploma thesis consists of a design concept of ultrasonic flow meter usable in an explosive environment. Furthermore, thesis contains strength and displacement control of important components of the design concept using the final element method. The model, drawings and calculations were&...

The diploma thesis contains a mapping of all energy losses and consumption of a tram vehicle and a proposal of a system of measures that contribute to the reduction of energy consumption and reduction of operating costs of a tram vehicle.

The thesis contains a research in the field of boggies for tram vehicles. Three conceptual boggies designs were created, one of them was selected and detailed. The calculation of the forces loading the boggie frame was carried out according to the relevant standards and the&#x...