Full metadata record
DC poleHodnotaJazyk
dc.contributor.authorPolák, Roman
dc.contributor.authorZahálka, Martin
dc.date.accessioned2019-03-04T11:50:33Z-
dc.date.available2019-03-04T11:50:33Z-
dc.date.issued2018
dc.identifier.citationPOLÁK, R., ZAHÁLKA, M. Influence of gate position during the injection moulding process. In: Annals of DAAAM and Proceedings of the International DAAAM Symposium. Vídeň, Rakousko: DAAAM International Vienna, 2018. s. 659-664. ISBN 978-3-902734-20-4 , ISSN 1726-9679.en
dc.identifier.isbn978-3-902734-20-4
dc.identifier.issn1726-9679
dc.identifier.uri2-s2.0-85060102790
dc.identifier.urihttp://hdl.handle.net/11025/31136
dc.format6 s.cs
dc.format.mimetypeapplication/pdf
dc.language.isoenen
dc.publisherDAAAM International Viennaen
dc.relation.ispartofseriesAnnals of DAAAM and Proceedings of the International DAAAM Symposiumen
dc.rightsPlný text je přístupný v rámci univerzity přihlášeným uživatelům.cs
dc.rights© DAAAM International Viennaen
dc.titleInfluence of gate position during the injection moulding processen
dc.typekonferenční příspěvekcs
dc.typeconferenceObjecten
dc.rights.accessrestrictedAccessen
dc.type.versionpublishedVersionen
dc.description.abstract-translatedThis article deals with the influence of the gate position on the final properties of a plastic product after the injection moulding process. Parameters such as temperature, fibre orientation and filling velocity are evaluated. The importance of the internal fibre orientation on the mechanical properties is also described. Advanced virtual mould-flow analysis is used for this research. A simple brick from Polybutylene Terephthalate (PBT) with 30% of short glass fibres is chosen as the reference part. A virtual model of PBT is described in depth in this article. An injection process with the same initial parameters was used for three different locations of the pin gate. This type of gate is considered because it is one of the most frequently used in the plastics industry. Different kinds of gates and their influence on filling are also briefly described. This paper shows the importance of the gate location and it also helps to understand the flow of short fibre reinforced thermoplastics inside the mould cavity. The article presents an in-depth and complex view of the issue of mould filling.en
dc.subject.translatedinjection mouldingen
dc.subject.translatedgateen
dc.subject.translatedfillingen
dc.subject.translatedfibre orientationen
dc.identifier.doi10.2507/29th.daaam.proceedings.095
dc.type.statusPeer-revieweden
dc.identifier.obd43924171
dc.project.IDLO1502/RoRTI - Rozvoj Regionálního technologického institutucs
Vyskytuje se v kolekcích:Konferenční příspěvky / Conference papers (KKS)
OBD

Soubory připojené k záznamu:
Soubor VelikostFormát 
INFLUENCE OF GATE POSITION DURING THE INJECTION MOULDING PROCESS.pdf1,05 MBAdobe PDFZobrazit/otevřít  Vyžádat kopii


Použijte tento identifikátor k citaci nebo jako odkaz na tento záznam: http://hdl.handle.net/11025/31136

Všechny záznamy v DSpace jsou chráněny autorskými právy, všechna práva vyhrazena.

hledání
navigace
  1. DSpace at University of West Bohemia
  2. Publikační činnost / Publications
  3. OBD