Full metadata record
DC poleHodnotaJazyk
dc.contributor.authorBenešová, Soňa
dc.contributor.authorPrůcha, Vojtěch
dc.contributor.authorVeselý, Vilém
dc.contributor.authorKesl, Miloslav
dc.contributor.editorKučerová, Ludmila
dc.contributor.editorJirková, Hana
dc.contributor.editorJeníček, Štěpán
dc.date.accessioned2019-10-08T10:41:01Z-
dc.date.available2019-10-08T10:41:01Z-
dc.date.issued2019
dc.identifier.citationJIRKOVÁ, Hana ed.; JENÍČEK, Štepán ed. Proceedings PING 2019: modern trends in material engineering: 10.-13.09.2019, Pilsen. 1. vyd. Plzeň: University of West Bohemia, 2019, s. 26. ISBN 978-80-261-0879-5.en
dc.identifier.isbn978-80-261-0879-5
dc.identifier.urihttp://hdl.handle.net/11025/35215
dc.description.sponsorshipPING 2019 is organized with the support of funds for specific university research project SVK1-2019-002.en
dc.format1 s.cs
dc.format.mimetypeapplication/PDF
dc.language.isoenen
dc.publisherUniversity of West Bohemiaen
dc.rights© University of West Bohemiaen
dc.subjectrychlořezná ocelcs
dc.subjectkovánícs
dc.subjectvelikost zrna austenitucs
dc.subjectkruhovitostcs
dc.titleEffects of hot forging on the shape and size of prior austenite grain in HS 6-5-2 high-speed steelen
dc.typekonferenční příspěvekcs
dc.typeconferenceObjecten
dc.rights.accessopenAccessen
dc.type.versionpublishedVersionen
dc.description.abstract-translatedMicrostructure analysis was performed on rolled bars of high-speed steel after two and three forging cycles, each cycle comprising one upsetting and one drawing out operation. High-speed steels belong to difficult-to-form materials with a narrow forging temperature interval. Forging above the maximum forging temperature may lead to grain coarsening. Below the minimum forging temperature, deformation resistance of the material increases, and the workpiece may fail. Using numerical modelling, special forging dies were designed and effective strain distribution was calculated for an axial cross-section plane in specimens after two and three forging cycles. The purpose of the analysis was to identify the relationship between the amount of effective strain and the shape and size of austenite grain after forging. The size of prior austenite grains was measured using the linear intercept method which is based on the Snyder-Graff method. Grain shapes were characterized in terms of circularity, which is the difference between the shape in question and a circle. With increasing amount of strain, the grains in the material became finer, as undissolved carbides impeded grain growth. In as-received rolled condition, the austenite grain size was G9. After three forging cycles, it was smaller, G11 (the higher the number, the smaller the grains). Circularity characterizes the complexity of a grain shape. After deformation, strongly non-circular grains were found in the material, although a certain portion of grains retained their round shapes. This was reflected in greater variance of circularity after the forging cycles.en
dc.subject.translatedhigh-speed steelen
dc.subject.translatedforgingen
dc.subject.translatedaustenite grain sizeen
dc.subject.translatedcircularityen
dc.type.statusPeer-revieweden
Vyskytuje se v kolekcích:Proceedings PING 2019: modern trends in material engineering
Konferenční příspěvky / Conference papers (KMM)
Proceedings PING 2019: modern trends in material engineering

Soubory připojené k záznamu:
Soubor Popis VelikostFormát 
Benesova.pdfPlný text180,63 kBAdobe PDFZobrazit/otevřít
Zobrazit minimální záznam Zobrazit statistiky


Použijte tento identifikátor k citaci nebo jako odkaz na tento záznam: http://hdl.handle.net/11025/35215

Všechny záznamy v DSpace jsou chráněny autorskými právy, všechna práva vyhrazena.

hledání
navigace
  1. DSpace at University of West Bohemia
  2. Publikace ZČU / UWB Publications
  3. Sborníky ZČU / UWB Proceedings
  4. Proceedings PING: modern trends in material engineering
  5. Proceedings PING 2019: modern trends in material engineering