This bachelor thesis deals with the measurement techniques in heat and chemical-heat treatment operations . It provides a brief overview of the measuring instruments used in the industry. It also deals with measuring instruments that are used on the line of chemical-heat treatment ...

This bachelor project verifies possibilities of using the methods of image analysis which is used to determine the quality of the tangible castings. The finding primarily serves as a guide for proper use of the software. The work was created on the basis of significant bi...

Theoretical part of this thesis deal with the characterization and production of new types of inorganic binders. The experimental part of the work is focused on the preparation of granular two-component aluminosilicate composite and exploring of its properties by measuring of the ...

This work deals with pickling heterogeneous products. These products were created by welding martensitic steels and austeniticferritic steels. In the practical part are heterogeneous products pickled in experimentally developed pickling baths of various concentrations, at different temperatures pickling ba...

This thesis deals with the technological and mechanical properties of weld joint of thick plate on the upper Chamber of the vulkanizing press and design a new Welding Technology. The original technology of a Welding Technology is replaced by more productive something technology. Th...

Bachelor thesis contains a general theory of glue and fatigue adhesive joints. The theoretical part deals with the basic division of glues, compare bonding technique with other techniques and describe normative tests on glues. The practical part contains the processed results of the...

This Bachelory work focuses on the theory of material degradation due to wear. The theoretical part describes the types of wear and gives an overview of metallic wear-resistant alloys. Especially for chromium irons is relationship between microstructure and wear-resistance highlighted. Experiment...

The aim of this work is to compare characteristics of two tested tool steels X37CrMoV5-1 (19 552) and HS6-5-2-5 (19 852) after the classic and the cryogenic heat treatment, further to evaluate the effect of nitriding after different heat treatment methods: hardness and microhardnes...

This thesis deals with the relationship between surface roughness and machining methods for fatigue properties of the material. It is divided into a theoretical part where the integrity of the surface is described and a practical part, where it was necessary to measure surface ...

This thesis deals with various technologies of the material surface blackening, Particularly the technology of the alkaline blackening. After a brief introduction to the thesis, Which deals with the general view on this subject followed by a chapter dealing with the Material surface...

This Bachelor thesis describes the metals Al, Sn and the metastable alloy of their Al-Sn combination. The main objective of this work was an attempt to create this alloy using the laser-induced CVD method. Tetramethyltin and trimethylaluminium were used as reactants. The following ...

This bachelor thesis is focused on laser induced synthesis of nanocomposites based on semiconducting Ge-C and Te-C. These deposits were created using pulse laser ablation of Te and Ge target by simultaneous decomposition of hexane of dielectric breakdown. Obtained deposits we analyzed b...

This work deals with adjustment microgeometry of cutting edge of axial instruments. Tools were made from three kinds of sintered carbides. The aim is to map the tumbling parameters in relation to the surface condition and edge microgeometry. These findings will be put into con...

The aim of the thesis is the optimalization of thin layers measuring method for rating of polymer materials that have been layered by long-time application in high temperature. Thermal Aging was measuered on cylinder shaped samples of polymers used for production of electric insula...

This bachelor thesis deals with heat treatment for steels called Quenching and Partitioning which is modified by an incremental deformation. Experiment was performed on three steels with constant content of carbon and different contents of silicon and manganese. The effect of cooling&#...

Bachelor thesis contains a description of the technological features and a description of testing the mechanical properties of compensation coated electrodes for welding in nuclear power industry.

This bachelor thesis deals with quantitative evaluation of minority phases in the steel CB2 which belongs by the chemical composition to so called modified (9-12)%Cr steels after a creep exposition. Evaluated image were taken at transmission and scanning electron microscopes and they we...

The bachelor´s thesis is divided into two parts ? theoretical and experimental. The theoretical part is focused on common ways of heat treatment and the vast majority is devoted to laser surface hardening technology and induction hardening technology. Firstly, the experimental part eval...